How To Lace a Motorcycle Wheel | Rocky Mountain ATV/MC

  • 🎬 Video
  • ℹ️ Published 7 years ago
preview_player
UCQSXoYEPBXNPSx1hWbO2WRQ



Click Here To Subscribe To Our Channel!

💬 Comments
Author

I put triflow on the nipples every couple of months to make sure they never freeze up. also spray the spokes with lube before adding the nipples. It will make assembly smoother and eliminate binding when tightening.

Author — Steve Hangen

Author

My kx's rear wheel spokes got snapped when i was trying to tighten them so this is most definitely helpful

Author — That kx guy

Author

Can you replace one spoke at a time instead of of removing all of them and replacing all of them?
For example loosen all of them but ONLY replace one spoke at a time ?

Author — Charles Cummings

Author

Make sure you don’t need all spikes, but the Iner and outer spokes need to line up.

Author — Macro Games

Author

Would I follow the same procedure to lace a 32, and a 28 spoke wheel. I have a CRF 150RB with 19" and 16" wheels.

Author — Thomas Sylvestro

Author

What is the most common size of the hole on the rim

Author — karlosfz07

Author

can somebody tell me what size spoke wrench I need for a ttr 230 front tire? also I can't find spokes for it anywhere so I'm assuming they are interchangeable with some other bike?

Author — Tom

Author

What kind of motorcycle wheel is that one?, I have a Tusk rim and spoke kit for a 2007 crf450r and the spokes seem to be too long, maybe I need a different pattern than the one shown here?

Author — MJNader

Author

What size of bit are you using on the drill to tighten the spokes?

Author — Riley Genereux

Author

What a shot! Hahah that was pretty awesome

Author — TackleShopBoys

Author

Isn't it important which spoke and hole you start with?  I once built a bicycle wheel but started with the wrong spoke, which resulted in the valve stem being located under a pair of crossed spokes.  This made it almost impossible to inflate the tire!

Author — SatansSpatula

Author

Thank rocky mountain atv mc for this info..

Author — TFV YouTube

Author

Whenever I swap out a tube and tire, I always clean my rims, and spray some WD-40 on the nipples, wipe off the excess and install the rim band. NEVER use duct tape.
My 1995 CR250R wheels look as good as my ‘19 wheels, just not
A spoke torque wrench is a great tool to own. Takes the guesswork out of it. Spokes are to be checked before every ride, just like your tire pressure. Especially on a new bike.
You didn’t mention anything about offset.

Author — chipper442

Author

spoke salvage last about 5 years they tend to season or break after five years

Author — Gareth Davies

Author

Consider changing your voice over at the beginning of the video to have the viewer note the difference between any spokes as visible PRIOR to disassembly of the original wheel/rim configuration to determine that which could avoid having to hunt down the manufacturer's information about spoke type, placement, and orientation?

Author — John Houman

Author

Hi Guys, do you anyone that supply a new set of anodised wheels/hubs for a 1991 Yamaha YZ125 please? 🙏🏻✊🏻

Author — Scott Porter

Author

hi, can i rebuild a wheel without changing the hubs? the rims i have came from aprilia mx 125 and the hubs came from derbi terra 125? possible?

Author — For Tumblr

Author

can be dangerous driving DT with 25 spokes 10 Ms in manufacturers recommend to replace all sports not 10 all depends if they in great condition

Author — Gareth Davies

Author

I'm lacing the front wheel with tusk rim and tusk 21"spokes on a crf 450r 2007,

Author — MJNader

Author

Great job mentioning the dish measurement @.@

Author — EnglertRacing96